8.13.2. Capacitive Half Wave Rectification Post Zener

#r# This example shows a capacitive power supply with a post zener half-rectification, a kind
#r# of transformless power supply.

#r# To go further on this topic, you can read these design notes:
#r#
#r# * Transformerless Power Supply Design, Designer Circuits, LLC
#r# * Low-cost power supply for home appliances, STM, AN1476
#r# * Transformerless Power Supplies: Resistive and Capacitive, Microchip, AN954

####################################################################################################

import matplotlib.pyplot as plt

####################################################################################################

import PySpice.Logging.Logging as Logging
logger = Logging.setup_logging()

####################################################################################################

from PySpice.Doc.ExampleTools import find_libraries
from PySpice.Probe.Plot import plot
from PySpice.Spice.Library import SpiceLibrary
from PySpice.Spice.Netlist import Circuit
from PySpice.Unit import *

####################################################################################################

libraries_path = find_libraries()
spice_library = SpiceLibrary(libraries_path)

####################################################################################################

#f# circuit_macros('capacitive-half-wave-rectification-post-zener-circuit.m4')

circuit = Circuit('Capacitive Half-Wave Rectification (Post Zener)')

circuit.include(spice_library['1N4148'])
# 1N5919B: 5.6 V, 3.0 W Zener Diode Voltage Regulator
circuit.include(spice_library['d1n5919brl'])

ac_line = circuit.AcLine('input', circuit.gnd, 'L', rms_voltage=230@u_V, frequency=50@u_Hz)
circuit.R('in', 'L', 1, 470@u_Ω)
circuit.C('in', 1, 2, 470@u_nF)
circuit.X('Dz', 'd1n5919brl', circuit.gnd, 2)
circuit.X('D', '1N4148', 2, 'out')
circuit.C('', circuit.gnd, 'out', 220@u_uF)
circuit.R('load', circuit.gnd, 'out', 1@u_kΩ)

#?# Fixme: circuit.nodes[2].v, circuit.branch.current
# print circuit.nodes

# Simulator(circuit, ...).transient(...)
simulator = circuit.simulator(temperature=25, nominal_temperature=25)
analysis = simulator.transient(step_time=ac_line.period/200, end_time=ac_line.period*10)

figure, ax = plt.subplots(figsize=(20, 10))

ax.plot(analysis['L'] / 100)
ax.plot(analysis.out)
###ax.plot((analysis.out - analysis['L']) / 100)
###ax.plot(analysis.out - analysis['2'])
###ax.plot((analysis['2'] - analysis['1']) / 100)
# or:
#   plt.ax.plot(analysis.out.abscissa, analysis.out)
ax.legend(('Vin [V]', 'Vout [V]'), loc=(.8,.8))
ax.grid()
ax.set_xlabel('t [s]')
ax.set_ylabel('[V]')

plt.tight_layout()
plt.show()
#f# save_figure('figure', 'capacitive-half-wave-rectification-post-zener.png')

This example shows a capacitive power supply with a post zener half-rectification, a kind of transformless power supply. To go further on this topic, you can read these design notes:

  • Transformerless Power Supply Design, Designer Circuits, LLC

  • Low-cost power supply for home appliances, STM, AN1476

  • Transformerless Power Supplies: Resistive and Capacitive, Microchip, AN954

import matplotlib.pyplot as plt


import PySpice.Logging.Logging as Logging
logger = Logging.setup_logging()


from PySpice.Doc.ExampleTools import find_libraries
from PySpice.Probe.Plot import plot
from PySpice.Spice.Library import SpiceLibrary
from PySpice.Spice.Netlist import Circuit
from PySpice.Unit import *


libraries_path = find_libraries()
spice_library = SpiceLibrary(libraries_path)
../../_images/capacitive-half-wave-rectification-post-zener-circuit.png 
circuit = Circuit('Capacitive Half-Wave Rectification (Post Zener)')

circuit.include(spice_library['1N4148'])
# 1N5919B: 5.6 V, 3.0 W Zener Diode Voltage Regulator
circuit.include(spice_library['d1n5919brl'])

ac_line = circuit.AcLine('input', circuit.gnd, 'L', rms_voltage=230@u_V, frequency=50@u_Hz)
circuit.R('in', 'L', 1, 470@u_Ω)
circuit.C('in', 1, 2, 470@u_nF)
circuit.X('Dz', 'd1n5919brl', circuit.gnd, 2)
circuit.X('D', '1N4148', 2, 'out')
circuit.C('', circuit.gnd, 'out', 220@u_uF)
circuit.R('load', circuit.gnd, 'out', 1@u_kΩ)

# print circuit.nodes

# Simulator(circuit, ...).transient(...)
simulator = circuit.simulator(temperature=25, nominal_temperature=25)
analysis = simulator.transient(step_time=ac_line.period/200, end_time=ac_line.period*10)

figure, ax = plt.subplots(figsize=(20, 10))

ax.plot(analysis['L'] / 100)
ax.plot(analysis.out)
###ax.plot((analysis.out - analysis['L']) / 100)
###ax.plot(analysis.out - analysis['2'])
###ax.plot((analysis['2'] - analysis['1']) / 100)
# or:
#   plt.ax.plot(analysis.out.abscissa, analysis.out)
ax.legend(('Vin [V]', 'Vout [V]'), loc=(.8,.8))
ax.grid()
ax.set_xlabel('t [s]')
ax.set_ylabel('[V]')

plt.tight_layout()
plt.show()
../../_images/capacitive-half-wave-rectification-post-zener.png